Olive Oysterling, also known as "Mukitake," is a thick gilled mushroom with an oyster shell shape. Fresh mushrooms, when sliced and sautéed, are buttery in texture and make for a delicious last harvest in late fall. Inoculating logs is simple and straightforward. Maintaining and managing logs is a matter of moisture management and patience. Before you begin, please be sure you have good quality logs to make the best possible mushroom growing experience.
Follow the five steps below for inoculating and managing your Olive Oysterling logs.
1. Cut the logs
Healthy, living trees should be cut during the dormant season and rested a minimum of 2 weeks prior to inoculating to allow a slight drying of the wood. Protect the logs from excessively drying out by storing them low to the ground (but out of the soil and leaf layer), out of the sun and wind, and where they can receive natural rainfall. Logs can be rested until inoculation for longer than 2 weeks, however there is increased risk of contamination and losing vital log moisture beyond 6 weeks.
*Logs can be cut to size for either the Drill-and-Fill Inoculation Method using standard log sizes (3-8˝ diameter x 36-40˝ length) or the Totem Inoculation Method using larger diameter logs (6-12" diameter x 6-12" length).
NOTE: Logs can be cut to size for either the Drill-and-Fill Inoculation Method using standard log size (3-8" diameter x 36"-40" length) or the Totem Inoculation Method using larger diameter logs (6-12" diameter x 6-12" length).
Drill-and-Fill Method
2. Drill the holes
Drill the holes to a 1˝depth following the diamond pattern (Figure to right) for roughly 50 holes per log. Plug spawn requires a 8.5mm (5/16˝) drill bit, and sawdust spawn typically requires a 12mm (7/16˝) drill bit.
3. Inoculate and seal with wax
Plug spawn: Use a hammer and gently tap in one plug per hole so it is flush with the surface of the log. Seal each plug with melted wax or plug wax.
Sawdust spawn: Break apart the spawn and inject it into each of the holes, typically with use of an inoculation tool.
Wax the holes as the logs are inoculated to protect the spawn from drying out and reduce the risk of contamination. Be sure the hole is completely sealed. Waxing the ends of the logs is not necessary. Sealing plug spawn with plug wax is an easy alternative to melting cheese wax and is easily applied using your finger as if you're applying lip balm over the end of the plug and hole opening. Hot wax is faster to apply and works better with sawdust spawn. Consider using wax daubers or the Okuda wax applicator. The flash point of cheese wax is 450°F. Do not overheat the wax! Turn down the heat if the wax begins to smoke.
4. Label the logs
Labeling logs with mushroom type and date inoculated can be very helpful - especially as you continue to build up your log inventory. We use aluminum tags (information is etched into the tag with a pen) or other labels, and staple them into the ends of the logs.
5. Incubate logs and manage for moisture
Once inoculated, place your logs in a shaded area, protected from the sun and wind, low to the ground or directly on the ground, and where they can receive natural rainfall. Maintaining moisture during this phase is the most critical step to mushroom production success. We recommend your logs receive 1˝ of rain per week. If it is dry, you may need to sprinkle your log heavily but infrequently. Logs will produce mushrooms in the fall after planting when the conditions for fruiting are ideal.
6. Mushroom harvest
Watch your logs closely in the fall and early winter when the temperature dips into the 40s (°F.). Harvest mushrooms by twisting them off the log and store them in the refrigerator until used.
Time to plant:
Typically spring, but throughout the growing season.
Time to fruiting:
Fall, often second year after inoculation.
Logs grown on:
Hardwoods like Sugar Maple, Beech, and Oak.
Plug spawn:
Approximately 50 plugs per log.
Sawdust spawn:
10-12 logs per 2.5 lb. bag; 20-25 logs per 5 lb. bag.
Appearance:
Oyster-like but lacking much of a stem. Cap is velvety and mustard-toffee-olive colored.
Flavor and texture:
Buttery texture brought out best through long, slow cooking.
Totem Inoculation Method
Place one cup of sawdust spawn in the bottom of a plastic garbage bag or large leaf bag. Set the log squarely on top of the spawn inside the bag (cut ends facing up and down). Sprinkle enough spawn on top of the log to cover it ⅛˝ to ¼˝deep. Set another log on top of this and sprinkle more spawn. Cover and cap the top log with newspaper or brown paper bag and secure it onto the log (large rubber bands work well for this). You can also use a thin slice of log to cap the top. Close up the bag with a small rubber band leaving a slight opening for air exchange. Ideally they should be placed in an area with constant temperature between 60-80°F for 4-6 months.
Once the incubation phase is complete (you should see white fuzzy growth on the logs), remove the logs from the bag and place upright outdoors in a shady area where they are out of the wind and can receive natural rainfall. Logs will produce mushrooms in the late fall when the temperature dips into the 40s (°F). Harvest as described in Step 6.
$21.00–$45.00
